Why insert the plug into the screwdriver and 7 more tricks house masters

  • Dec 24, 2019

When the repair or construction work to save time, and save the nerve cells to help a variety of useful tricks and techniques. Sometimes they are very simple, but do not come to mind to everyone. The material Novate.ru a small selection of useful tips masters - aces of the business, which can come in handy handyman.

1. How to make a tube that dotyanet in any place

During the repair work happens that in some remote place need to apply adhesive or gently put a drop of oil or some other means. To make it possible to accurately using a syringe and a narrow heat-shrinkable tube. Cut piece of the desired length of the tube, is pushed onto the tip of the syringe, of course, without the needle, and shrunk uniformly heating over the entire length. Act carefully, taking care not to accidentally solder the end of the syringe. After cooling down, get a kind of compact tube with a long flexible spout that podlezet almost anywhere.

With such a long spout can reach any hard points
With such a long spout can reach any hard points

2. How to store compact extender

Household extension cords irreplaceable thing in the economy. The only thing, no matter how we turn off the wire, anyway, he will be confused, and store it in a way inconvenient. A small upgrade solves this problem. Only two hooks and a small piece of wood, need for it. Well, a little time and effort.

Pre-mark the point, and at this point in the bracket holes are drilled, so you could collect shoe
Pre-mark the point, and at this point in the bracket holes are drilled, so you could collect shoe

Block Extension dismantled, screws neatly folded. The lower part of the pad is applied to the middle of the boards and mark the assembly point where the screws are screwed. At these points in bar zasverlivayut holes that then can be collected back design.

The wire is wound on the eight hooks
The wire is wound on the eight hooks

Thereafter the lower part is attached to the pads plaque: on its corners zasverlivayut holes for screws and screwed fasteners.

>>>>Ideas for life | NOVATE.RU<<<

Next block is collected back by screwing screws through holes made in advance in the plaque. On the reverse side strap fastens around the edges of the hooks. That's all for the device compact and neat winding wires ready.

Helpful advice from Novate.ru: To work during the accident not to lose the screws, which can be the lag can use masking tape or duct tape. Tear off a piece of tape, and when disassembling the pads glued on it fixing elements. So they drove off to the floor.

3. How to quickly remove metal shavings

Resulting from the treatment of metal shavings can be easily and quickly removed without dustpan and broom. In a plastic bag put the magnet and lead them on the work surface. All the chips just "fly" themselves, attracted by the magnetic field. After complete stripping of the working

seat bag turned inside, and all metal mote is inside. That's all. One can only throw in the trash bag.

Magnet Service - simple and secure way to hand cleaning metal shavings
Magnet Service - simple and secure way to hand cleaning metal shavings

4. How to make a protective cover for Dremel

For working with Dremel will be very useful is such a thing as a small plastic casing. It can be easy to do it yourself and for free. To pick up tips plastic bottle with a wide neck suitable diameter. The vessel must be transparent, with a smooth surface without any grooved patterns, impeding visibility.

The cover doing a hole of suitable size
The cover doing a hole of suitable size

In the bottle cut off the top, cut it in half, giving shape and the edges slightly sovochkom zashlifovyvayut. The lid of the bottle is drilled sufficiently wide opening. On Dremel spun nut and cap nut put back spin. Then fasten the trimmed portion of the bottle and get a simple cover.

The casing protects against flying sparks
The casing protects against flying sparks

Of course, for the master obligatory sunglasses that protect the eyes from chips and sparks. But this self-made housing more than not - in the face of sawdust will fly less. Its only drawback - the plastic bottle is afraid of high temperatures, and when grinding metal will thicken from hot sparks. But when used regularly, it is a good alternative to the factory nozzles. In addition, you can always make a new one.

5. How to make handles for small tools

Used toothbrushes have in every home and most people throw them immediately. But they can be used for any other purposes. In particular, they make beautiful pens for small tools. For example, for the Needle. Agree, because with models that do not have handles, work is not very convenient. But this can be easily remedied.

A good master in the case goes and toothbrush
A good master in the case goes and toothbrush

In the toothbrush cut upper portion with bristles. The sliced ​​thin drill handle zasverlivayut hole diameter slightly less than the shank Needle. Next, the tool shank is heated (e.g., above the plate) and pushed onto the handle of a brush. Plastic from the hot metal will float slightly and gripped needle file.

6. How to get a sleeve with a dull landing

Sometimes it is that you want to get a bush with a dull landing. For example, faced with the owners of the Bulgarians, when it comes time to replace worn internal parts. Bush sits very tight, and get to it from the other side can not. You can, of course, it nasverlit thread and pull with the bolt. But there is a much easier way to quickly pull the plug without damaging the part.

The grease and steam blows with a hammer - and the bush comes out
The grease and steam blows with a hammer - and the bush comes out

To this end, its interior space is completely filled with some kind of grease. Then is inserted a bolt or metal rod of suitable diameter and single hammer knock sleeve slowly.

>>>>Ideas for life | NOVATE.RU<<<

There is one drawback of using grease - it pollutes the surface and then have to spend time cleaning. To clean parts, you can use ordinary bread crumbs. Knead it well and completely fill all of the sleeve hole. Further emboss using the rod and the hammer as usual.

Crumb of bread - a great alternative to grease the extraction sleeve
Crumb of bread - a great alternative to grease the extraction sleeve

7. How fast to polish small parts

Grinding process parts tedious chore and particularly when small sized billets. You can speed up the work with the help of some flat wooden stick, such as skewers for barbecue.

Such a simple device simplifies fine grinding operation
Such a simple device simplifies fine grinding operation

Portion of the desired length is cut, it is wrapped with sandpaper, fixed to the ends of the tape and the cartridge is inserted into the screwdriver. If no skewers, it is possible to replace the conventional pencil.

8. Mixer plug and screwdriver

This all-male life hacking can be useful to women. When not at hand mixer, and you really need it, get help from savvy, fork and screwdriver. Instead, you can use a screwdriver and a very powerful drill.

Mixer screwdriver
Mixer screwdriver

So, pick up a fork with wide handles no more than 15 mm, because it is the maximum possible diameter of the drill, screwdriver on which is calculated. Insert the plug into the screwdriver and all the brutal super-mixer ready.

An important advantage of this mixer is not only power, but also autonomy, because it operates on battery power.