With a simple life hacking windshield repair a crack can be anyone and effortlessly. Such a little trouble on the glass may occur suddenly, such as when a small stone bounces off the road and spoils the integrity of the machine. From similar accidents no one is immune. However, if all let things slide, then a small crack over time, can become more and more, not to mention the fact that it looks very ugly.
1. The crack on the windshield
Of course, a large crack on the windshield can be corrected only by its replacement. But here's a small defect, which resembles cobweb, it is possible to fix on their own. First you need to clean the glass with a cloth made of microfiber and alcohol. The liquid should be poured onto the fabric and not on the glass itself. For repairs will need a special kit that you can buy in the store of automotive products. Press-stud to gently hold for chips or cracks, to make sure there are no remaining pieces of glass. If necessary, get them.
Helpful advice from Novate.ru: To improve visibility, from the interior to the windshield is better to attach a piece of cardboard or paper. Since the crack will be more noticeable and correct it will be much easier.
2. crucial moment
In the next step you need to take a circle, remove the protection film and stick on the windscreen so that the crack was inside. It is important to make sure that the circle holding up well - for this it is necessary to firmly press down on the glass. Then remove the second protective part, leaving only the adhesive base. The next step - this circle neatly and glue nozzle right protruding part outwards.
This is what happens at this stage.
3. we use resin
Now is the time to use a resin, which was in the repair kit. Scissors cut away the top of the vial, only the edge, so that the content can be squeezed out. Insert the "nose" of the tube to the nozzle and extrude to three-quarters of the resin. Then change tube on the syringe and pulling air from the nozzle, thereby creating a vacuum inside. The syringe, you need to leave it at that for 10 minutes.
4. Important stage
After 10 minutes have passed, indicated in the instructions, you need to thoroughly and often to tap on the windshield near the nozzle, so that all the extra air bubbles out. From the side of the cabin, you can watch the whole process of vesicle release. This is followed by holding the base gently to get a syringe, and then plug it back in and push the plunger up to half to create air pressure. This action enables you to drive the resin into the crack. After this operation, all the reserve stationary for 20 minutes, the resin is stiffened.
5. The final phase correction windshield
Now, using a razor should be accurate to separate the nozzle from the windshield. It is necessary to be attentive and to prepare in advance a napkin to remove the remnants of the liquid resin at once. Taking the tube, it is necessary to squeeze out right on top of a drop of crack and put a yellow square on top of it. Use the razor blade to get rid of air bubbles under the plate. To do this well, but gently pressing, it is necessary to hold the blade on the yellow square. We reserve the resin for 15 minutes under direct sunlight. If the sun on this day does not shine or the machine is in the shade, you should wait at least an hour.
READ ALSO: How to remove superglue from the way the fingers proven effective
6. Redecorating
Having hooked a corner yellow square, remove it from the windshield. Beneath it is found a frozen pitch. To remove its excess balances and make the surface of the glass flat, you need to use all of the same blade. With it, you need to carefully and slowly remove unnecessary roughness. Need to press the blade as close to the glass, but without scratching it. Thus any excess resin scraped off. Cracks are no more! Instead, if a very good look closely, you will notice a small spot, which is slightly different in color from the main part of the windshield. However, it can be considered minor compared to the fact that the crack could increase in size and ruin the visibility on the road.
7. Boiling water and body repair
To repair a dent very real. Another impressive life hacking, which will carry out repairs without unnecessary costs money. All that is needed for this - it's the teapot with hot water and plunger. Water should be boiled and then gently pour the boiling water over the dent and the area around it. Then you need to put the plunger in the area next to the dent and pull over carefully. Slowly and carefully, you need to repeat these steps around the dent, gradually moving closer to the main deformation. After a few minutes of hard work dent completely disappear, and no one would guess that it was there before.
>>>>Ideas for life | NOVATE.RU<<<<
Nothing is impossible and to completely repaired crack in the wood products.
A source: https://novate.ru/blogs/160819/51392/