The bathroom is our home spa where you can relax and spend some time alone. At the same time, soapy deposits, mold and dust accumulate here. And it is not uncommon to see scale or rust on and around the mixer. Agree, this significantly spoils the picture, and bathing becomes not so pleasant. We will show you how to properly maintain a clean bathroom and get rid of yellow enamel, limescale and rust. Bathing in a dirty bath is no fun
Types of pollution
1. Soap bloom
After taking water procedures, the remains of shower gels, shampoos and other products, together with keratinized particles of the epidermis, settle on the surface of the bath. As a result, a dense layer of dirt forms in the bathing tank, which eventually takes on an unpleasant tint.
2. Yellowed enamel
Yellow stains on a snow-white bathtub are the consequences of the formation of rust, which penetrates into the tank through old pipes. Layering on top of each other, the drips become richer and penetrate deeper into the bath coating.
3. Limescale
Often, plaque deposits on plumbing fixtures. Calcium salts in contact with soap form white streaks on tiles, taps and bathtubs. Another reason for them is hard water from the mains.
How to whiten a bath?
1. Enamel bath
Acidic solutions are suitable for products of this type. Do not scrub the enamel with an iron scraper or abrasive substances, as the coating may scratch or crack. Such damage is fraught with the development of mold and clogging of dirt.
1. Warm up the bath to intensify the chemical reaction and speed up the whitening. To do this, fill the tank with as hot as possible with water, and then drain and wipe dry.
2. Treat contaminated areas with concentrated vinegar, essence, or oxalic acid.
3. Leave it on for 15 minutes and then rinse the tub thoroughly with warm water.
2. Cast iron bath
A cast iron bath will be well bleached by a combination of soda and abrasives, as well as liquid chlorine. It is better to refrain from using a metal scraper so as not to damage the coating.
1. Heat the tub with hot water and wipe dry.
2. Fill the reservoir with "Whiteness" or liquid chlorine. Means like "Domestos" and "Hedgehog" are also suitable.
3. Leave the liquid on for 15 minutes and then rinse the tub with warm water.
You can also use citric acid. Densely sprinkle powder on a wet, heated bathtub so that it adheres to the surface and forms a concentrated product. After 25 minutes, rub the reservoir with a cloth and then rinse.
3. Acrylic bathtub
Abrasives and powders are a bad idea as they will scratch the acrylic. It is important not to break the antibacterial film on the surface of the tank so that the bath lasts longer.
1. "Warm up" the bath with water and wipe dry.
2. Pour a glass of hot water and dissolve a spoonful of citric acid in it. Alternatively, mix 100 ml of vinegar and 20 g of salt.
3. Apply the solution to a sponge or cloth and buff the entire surface of the reservoir.
4. After 20 minutes, rinse off the residue with warm water.
4. Metal bath
Mostly rust appears on metal baths. You can get rid of it without the help of expensive household chemicals. It is enough to use alkalis and acids.
1. Rinse the glass jar and dry it.
2. Pour and stir with 100 ml of ammonia and 50 ml of hydrogen peroxide.
3. Apply to a cloth or sponge, treat the dirt liberally and leave.
4. After 20 minutes, rinse the tub with warm water.
5. Universal way
The salt and wine vinegar cleaning method is suitable for both baths and sinks.
1. Pour into a glass container and mix 100 ml of wine vinegar and 50 g of salt.
2. Heat the solution in the microwave to 70 degrees.
3. Apply the liquid to a cloth and treat any yellowed areas.
4. Wash off the solution after exactly 30 minutes. Do not overexpose to avoid ruining the bath lining.
What can not be used to bleach a bath
In order not to aggravate the condition of the bath, carefully study the composition of household chemicals and homemade substances. It is not recommended to use products based on ammonia, chlorine, acetone, formaldehyde, hydrochloric acid.
Care advice
If you adhere to the rules of bathroom care, you will significantly extend the life of the tank and will be able to avoid bleaching procedures.
1. After each bath, clean the bath with a sponge and liquid soap. This will help prevent bacteria and limescale build-up.
2. Plumbing also needs to be washed and then wiped clean with a dry cloth. Moisture will not accumulate on the surfaces, provoking the appearance of rust.
READ ALSO: 7 reasons why an apartment looks dirty even after thorough cleaning
3. Do not place metal bowls or buckets on the bottom of the acrylic tank to avoid scratching the surface. If damage is done, the bath can be refurbished with liquid acrylic.
4. If there are pets and you bathe them in the bathtub, be sure to cover the bottom with a rubberized mat to protect the covering from the claws of the four-footed.
>>>>Ideas for life | NOVATE.RU<<<<
Following these simple rules will allow you to enjoy bathing in a snow-white bath for a long time without dirt, plaque and rust. If the reason still lies in hard water, we recommend that you additionally read about the right remedy to get rid of lime deposits on sanitary and household appliances.
A source: https://novate.ru/blogs/110720/55257/