Experience comes with time, and many artists there are interesting ways to simplify the process of work, make arrangements for the organized storage of tools and much more. These techniques will be useful to adopt the newcomers, the first who took up the instrument, but also skilled craftsmen can find something new. Or maybe, these methods will give impetus to the imagination, and will come up with something else to her.
1. Practical hanging organizer for small things
For storage of metal products, fasteners and other small things usually used various improvised vessel - drawers, boxes, jars. In general, because of what is at hand. A suspension in a convenient location, you can make the organizers of plastic bottles. So do not rush to throw them out. Take the bottle and laterally in its upper part cut square window. Unscrew the lid and center drill hole. Take a piece of wire and one end of the hook is turned off or in the form of a circle. The second end is threaded into a hole in the cover bends and fixing it. Twirl a bottle, pour back fasteners and hung by a hook.
2. Case for storing rolls of WD-40 cans
Universal Technical Spray WD-40 can be found, perhaps, in the economy of any master, so it is multifunctional. For cans with this tool is attached a thin plastic tube for injecting into difficult places. And this tube tends to be lost permanently. To avoid this, there is genius in its simplicity, the reception, which will always keep it handy.
>>>>Ideas for life | NOVATE.RU<<<<
We take an ordinary ballpoint pen without a rod. Inside the case to push a small piece of masking tape, rolled into a ball. This closes the hole at the end of the rod. Housing attach the handle to the cartridge WD-40, put to the tube, and fasten the top of the case. Since tube will not be lost and will always be at hand.
3. Simple and practical magnetic miter box
For sawing of material at a predetermined angle required stuslo use. This simple device can be purchased in the store, but you can do it yourself. For manufacturing will need two small pieces of wood, and three or four neodymium magnet. One side of the bar mark up the middle and draw a line along the entire length.
Do not miss: 6 ways that will improve the Wi-Fi signal itself
Use a screwdriver or any other method to do the line label, placing them at regular intervals. In the marked locations to drill shallow holes and the deepening inserted magnets.
Two bars glue, putting an end to one end of the other at an angle of 90 degrees and the reliability of fastening screws. It is important that the bars are smooth, are perpendicular to each other and to the upper surface of the bar is perpendicular to the section plane. So we'll get a comfortable working miter box. Due to the attraction of the magnets hacksaw does not deviate from the plane of the bar, and cutting is carried straight out.
The practical fact of Novate.ru: This home-made will be more convenient to use than store-bought. Make it is not difficult and the work takes only 10-15 minutes. The store Miter are svobodnovaty grooves, because of what hacksaw hangs. And after a few cuts gap increases even more.
4. Eliminating gaps in the laminate
Laminate flooring is very popular, durable, and beautiful. But sometimes trouble in the form of a slot between the bars. This may be caused by different causes, such as bad or low quality base prepared locking splines compounds.
Do not miss:10 useful ways to use sandpaper in the house
Eliminate these gaps can own a very simple way. A piece of double-sided tape pasted on the defective strip and attach a piece of wood on top, pinning to the tape. Take a hammer and gently, commensurate force, beat on the piece of wood in the direction of the slit. As a result, it becomes strap in place and closes the gap.
5. As release circular saw from a jammed piece of material
Cut a round hole is not a problem, with a hole saw on the farm. However, periodically during use there is a problem with the wedging material balance within the nozzle. This circle has to pick out with a screwdriver or some other tool. It is much easier to remove it by using long screws. To this end, the fastening element is screwed into the wood until it stops. Screw reaching the base blade, wedged circle eject from the nozzle.
6. Organizers for the tool
Another simple and functional organizer can easily make the cans of the old and waste plastics cuttings pipes. On the canister do form layout, leaving a high rear wall and making a smooth transition to the sides to the lower front. Cut capacity on a given line and treat the edges with a file to avoid sharp edges.
>>>>Ideas for life | NOVATE.RU<<<<
Take any remnants of pipes made of plastic or rubber, make a mark at the height of the flanges and cut them. Laid long side against the canister bottom and fill tube pieces, fastened together by a glue. In the front part can be positioned once the containers unnecessary. We had a functional organizer: in the pipes is convenient to place tools and containers - various little things.
7. How to sharpen a pencil using a power screwdriver
Perhaps this is one of the most simple, at the same time spectacular life hacking in our review. To rapidly sharpened pencil should start to record in pencil screwdrivers, and then install a small speed. Next, insert a pencil sharpener and an edge in turn screwdriver. Bingo!
bonus: How to remove superglue from the way the fingers proven effective
Few experiences joy when superglue dries on the skin. If no action is taken to remove it, naturally cured, the material will go a very long time.
There are different ways of getting rid of superglue on your hands, and not all of them are effective. But this method did not let even a single person.
A source: novate.ru